Click on any item to add to the quote cart

Constructed with 6" channel with all components located
inside this channel thus giving maximum tool width.
Includes:
  # 50 pin chain with 5" saddle centers
  Hardened Wear Bars
  Water Cooled Tubes
  Sheet Piercing Bar
  Pneumatic Chain Tensioning
  Manual Oil Lubrication

Before you form a rail sprocket into your sheet, it may be time to look at our new slide rail system

Infeed Guide  GUD1039

Rail, Required information

Stripper Disk

Idler Sprocket

1. Need measurement from end of rail to center of idler sprocket. to insure chain will clear any adjustment bars as it goes around drive shaft sprocket.

2. Need overall length of rail.

3. Note: Some modification may be required on  existing rail stand-off.

CYL1862-1  TENSION CYLINDER (2)
FTG1173  1/8 COMP. ELBOW (2)
FTG1145  1/8 - 1/4 JIC 90 (2)
HSS1074  BRAIDED HOSE (2)
LUB1113  MANUAL OILER (2)
MFR1019  MUFFLER (2)
REG1052  1/4 MINI REGULATOR  (1)
TNK1013  AIR - OIL TANK  (1)
TUB1010  TEFLON TUBE (12")
HSS1002   *  (2-piece rail only) HOSE (2)
FTG1002  *  (2-piece rail only) FITTING (2)
FTG1232    3/8 to 1/8  hex bushing (2)

3/8 to 1/4 bell reducer (2)
3/8 to 1/4 hex bushing (2)
1/4 close nipple (2)
1/4 x 2 nipple (2)
1/4 x 4 nipple (2)
1/4 90 degree elbow (2)
1/2 to 1/4  hex bushing (1)
1/2 plug (1)
1/2 tee (1)
1/2 close nipple (1)

BAR1058 SLIDE BAR, STD.  (as required)
BAR1058-3 SLIDE BAR 18" (as required)
BAR1058-2 SLIDE BAR, (specify length)  (as required)
BAR1072 SLIDE BAR W/OIL GROOVE (2) (stripper end cyl mt.) STD
BAR1072-1 SLIDE BAR W/OIL GROOVE (2)
BAR1073-1 PIERCE BAR  (2)
BRK1030-1 CYL. TAKE UP BRKT.  (2)
BRK1031-1 DRIP OILER BRKT  (2)
GUD1038 SS HOLD DOWN (special option) 
GUD1039 INFEED GUIDES  (1 of each, LH & RH)
GUD1040 SS HOLD DOWN (special option) 
MNT1067 IDLER SPKT MOUNT  (2)
RAL1015-2 RAIL CHANNEL (stripper end cyl mt.) STD (specify length)  (2)
RAL1015 RAIL CHANNEL (pierce end cyl mt.) SPECIAL (specify length)  (2)
RAL1016-1 RAIL SPLICE PLATE (if required) (new design)  (as required)
RAL1017 RAIL ENDS, assy drawing only
SPK1018-1  * 50B18 IDLER SPKT W/BRGS  (4)
SPA1092 TAKE UP SPKT SPACER  (2)
SPA1092-1 TAKE UP SPKT SPACER  (2) (double spkt only)
SPA1093 INFEED SPKT SPACER  (2)
SPA1094 SLIDE BAR SPACER  (as required)
SPA1095 IDLER SPKT SPACER  (2)
SPK1018-1  50B18 IDLER SPKT W/BRGS  (4)
SPK1028-1  * 50B18 STRIPPER SPKT W/BRGS  (2)
SPK1028-3  * 50C18 DOUBLE STRIPPER SPKT W/BRGS  (2) (optional) 
TUB1013 COOLING TUBE (fits all, specify length)  (2)
WAS1001  1/2 X .047 SHIM  (4)
WAS1033  1/2 X .010 SHIM  (4)

CHN….     * PIN CHAIN (as required)